#31: Re: new 206 gti 138 owner Author: andy83, Location: stoke on trentPosted: Sat Sep 27, 2014 2:27 am ---- bulbs checked and in place and seem to be in good condition, next question is do the reverse lights have a fuse i could check?
#32: Re: new 206 gti 138 owner Author: andy83, Location: stoke on trentPosted: Wed Oct 01, 2014 10:40 am ---- iv fount the reverse light problem to be the reverse light switch so ordered a new one and will be fitting it this weekend
on another front iv now ordered a maniflow 4-1 manifold and a pair of powerflex bushes for the engine mounts and started to get the bits required to convert to the 180 inlet manifold, iv purchased a 306 gti 6 throttle bodie and icv. just gotta get the inlet and 180 alternator now.
#33: Re: new 206 gti 138 owner Author: Edward, Location: In the garagePosted: Wed Oct 01, 2014 1:15 pm ---- Pair of power flex mounts? You need three.
#34: Re: new 206 gti 138 owner Author: Project2062014, Location: CornwallPosted: Wed Oct 01, 2014 2:13 pm ----
andy83 wrote:
iv fount the reverse light problem to be the reverse light switch so ordered a new one and will be fitting it this weekend
on another front iv now ordered a maniflow 4-1 manifold and a pair of powerflex bushes for the engine mounts and started to get the bits required to convert to the 180 inlet manifold, iv purchased a 306 gti 6 throttle bodie and icv. just gotta get the inlet and 180 alternator now.
nice !
(De-cat) get the lambda extension. Get a flexi joint off the manifold !
#35: Re: new 206 gti 138 owner Author: andy83, Location: stoke on trentPosted: Wed Oct 01, 2014 2:40 pm ---- Ill link you up to the parts I got from powerflex.
Cheers for the heads up matey should imagine it will make a nice little improvement
#36: Re: new 206 gti 138 owner Author: andy83, Location: stoke on trentPosted: Wed Oct 01, 2014 11:04 pm ---- www.powerflexshop.com/...ad-use-206
Ref: 20 - Lower Rear Engine Mount Bush (1 Bush) - PFF50-306 +£29.88
it seems like the other one i ordered was for the 1.4 engine so it looks as if powerflex only do the one bush for the engine mount?
#37: Re: new 206 gti 138 owner Author: andy83, Location: stoke on trentPosted: Wed Oct 01, 2014 11:18 pm ---- going off the diagram it looks as if its the rhs engine mount, so ill need the gearbox mount/bush still and superflex/powerflex dont do them so id imagine i need to get a vibratechnics one?
#38: Re: new 206 gti 138 owner Author: Project2062014, Location: CornwallPosted: Thu Oct 02, 2014 1:08 pm ---- Strip out spare wheel frame jack etc rear seats+ plastics & remove old air inlet pipe and metal bracket & its quick as ! Much better on the road .Light weight front seats in my nxt mod .
I have not got mounts or bushes as of yet . Do need some soon . Il see how you get on then probably copy your order to get it right . Engine does move alot .. wish i could help more . 8-(
#39: Re: new 206 gti 138 owner Author: andy83, Location: stoke on trentPosted: Fri Oct 03, 2014 7:58 am ---- thats ok fella iv fount you guys on here to be very helpful cracking forum
iv now just purchased a 180 inlet manifold so only need the 180 alternator now and i should have all the bits required for the inlet conversion
#40: Re: new 206 gti 138 owner Author: andy83, Location: stoke on trentPosted: Mon Oct 06, 2014 8:12 am ---- so i received the gti 6 throttle bodie/icv and powerflex lower engine mount bush, 180 inlet should be here tomorrow or weds.
#41: Re: new 206 gti 138 owner Author: Project2062014, Location: CornwallPosted: Mon Oct 06, 2014 8:15 pm ---- What you doing with the egr pipe ? Also ivc goes ?
#42: Re: new 206 gti 138 owner Author: andy83, Location: stoke on trentPosted: Mon Oct 06, 2014 11:19 pm ---- egr i believe gets blanked off, icv is required as the old one cant be used ill tell you where it goes when fitting
#43: Re: new 206 gti 138 owner Author: andy83, Location: stoke on trentPosted: Wed Oct 08, 2014 6:15 am ---- Bit of an update for you iv got the car booked in for sat morning at psi tuning in Newcastle under Lyme to see whats what before I start adding the exhaust and Inlet manifolds plus a remap.
Will be interesting to see what shes got still.
#44: Re: new 206 gti 138 owner Author: andy83, Location: stoke on trentPosted: Thu Oct 09, 2014 8:43 am ---- another update for you all, iv decided to go for a supersprint exhaust manifold thats designed to fit the oe cat, so less hassle etc etc, we are limited for the amount of time the car can be off the road as the wife uses it for work each day.
iv also ordered a set of kw -40mm lowering springs this should still keep the ride height practical but give it a much better stance, and ordered the vibratechnics gearbox engine mount, im hoping to fit the manifold/mounts and lower it in 1 day then the wife can have it back to get to work.
#45: Re: new 206 gti 138 owner Author: Project2062014, Location: CornwallPosted: Thu Oct 09, 2014 3:03 pm ----
andy83 wrote:
Bit of an update for you iv got the car booked in for sat morning at psi tuning in Newcastle under Lyme to see whats what before I start adding the exhaust and Inlet manifolds plus a remap.
Will be interesting to see what shes got still.
wait . Fit exhaust manifold plus de-cat also fit the Inlet if you can .
4-1 manifold best for flow. one on Gumtree 50 quid a couple days ago .. then get it remapped for best results . Mrs aint gna be happy lol . Took me 4 hr exhaust manifold to cat fitted & welded.
Ive contacted 2/3 tuning comps and they will not help further after they are told of my first remap .
Ring psi .make sure they will run the car again & be able to remap it after your mods . If you go first like i did .after map i Fitted mods & no remap ! Wtf . Anyone out there in southwest ??
We are not responsible for comments posted by our users, as they are the property of the poster
Interactive software released under GNU GPL,
Code Credits,
Privacy Policy
Membership:
Latest: 
New Today: 0
New Yesterday: 0
Overall: 17112
Online Now [27]:
Visitors: 26
Members: 0
Staff Online Now:
Page Views:
General
